COMFILE Technology's Documentation Library

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
====== Synchronizing the Backlight with the X11 Screensaver ======


This program will turn the backlight ON or OFF according to the ON/OFF state of the display as reported by [[https://www.x.org/releases/X11R7.7/doc/xextproto/dpms.html|DPMS]] (run ''xset q'' from a terminal to see the DPMS report).

<code cpp>
#include <cstdlib>
#include <cstdio>
#include <X11/Xlib.h>
#include <X11/extensions/dpms.h>
#include <chrono>
#include <thread>
#include <sys/syslog.h>
#include <pigpiod_if2.h>
 
using namespace std;
using namespace std::chrono;
 
#define PIN 34  // CPi-A/B/F/S
// #define PIN 44 // CPi-C

void log_info(const char *const message)
{
    printf("%s\n", message);
    syslog(LOG_INFO, "%s", message);
}

void log_err(const char *const message)
{
    printf("%s\n", message);
    syslog(LOG_ERR, "%s", message);
}
 
void backlight_on()
{
    auto instance = pigpio_start(NULL, NULL);
    if (instance != 0)
    {
        log_err("pigpio_start did not return success");
        return;
    }
 
    auto result = set_mode(instance, PIN, PI_OUTPUT);
    if (instance != 0)
    {
        log_err("set_mode did not return success");
        return;
    }

    result = gpio_write(instance, PIN, 1);
    if (instance != 0)
    {
        log_err("gpio_write did not return success");
        return;
    }
 
    pigpio_stop(instance);
}
 
void backlight_off()
{
    auto instance = pigpio_start(NULL, NULL);
    if (instance != 0)
    {
        log_err("pigpio_start did not return success");
        return;
    }
 
    auto result = set_mode(instance, PIN, PI_OUTPUT);
    if (instance != 0)
    {
        log_err("set_mode did not return success");
        return;
    }

    result = gpio_write(instance, PIN, 0);
    if (instance != 0)
    {
        log_err("gpio_write did not return success");
        return;
    }
 
    pigpio_stop(instance);
}

void set_backlight(CARD16 state)
{
    switch (state)
    {
        case DPMSModeOn:
            log_info("Turning backlight on");
            backlight_on();
            break;
        case DPMSModeOff:
            log_info("Turning backlight off");
            backlight_off();
            break;
        default:
            log_info("Invalid state");
            break;
    }
}
 
int main(int argc, char *argv[])
{
    openlog("backlight_service", LOG_NDELAY, LOG_USER);

    log_info("Starting");

    Display *dpy;
    dpy = XOpenDisplay(NULL);
    if (dpy == NULL)
    {
        log_err("Unable to open display");
        exit(EXIT_FAILURE);
    }
 
    BOOL onoff;
    CARD16 last_state;
    CARD16 state;

    // Initialize last_state
    if (!DPMSInfo(dpy, &state, &onoff))
    {
        log_err("DPMSInfo returned FALSE");
    }
    set_backlight(state);
    last_state = state;

    while(true)
    {
        if (!DPMSInfo(dpy, &state, &onoff))
        {
            log_err("DPMSInfo returned FALSE");
            this_thread::sleep_for(seconds(2));
            continue;
        }

        // If DPMS is not enabled, then display a message
        if (!onoff)
        {
            log_err("DPMSInfo is not enabled");
            this_thread::sleep_for(seconds(2));
            continue;
        }

        if (last_state != state)
        {
            set_backlight(state);

            last_state = state;
        }
        this_thread::sleep_for(milliseconds(200));
    }
 
    XCloseDisplay(dpy);

    log_info("Exiting");
 
    return 0;
}
</code>


==== Compile ====
Add the necessary development packages ...
<code>
sudo apt install libx11-dev libxext-dev
</code>
... then compile.
<code>
g++ backlight_service.cpp -lX11 -lXext -lpigpiod_if2 -o backlight_service
</code>

==== Bash Script Implementation ====
The same can be a achieved using the following Bash script:

<code bash>
#!/bin/bash

PWM_PIN=31
PIN=34

# Set pins as output
raspi-gpio set $PWM_PIN op
raspi-gpio set $PIN op

# Start with both pins HIGH.  If either of the
# pins go LOW, the backlight will turn off.
raspi-gpio set $PWM_PIN dh
raspi-gpio set $PIN dh

# Get the current state
CURRENT_STATUS=$(xset q | grep "Monitor is" | awk '{print $3}')
LAST_STATUS=$CURRENT_STATUS

logger -p info -t "backlight_service" -s "Monitor is $CURRENT_STATUS"

# Loop indefinitely updating backlight in sync with monitor status
while true; do

  # Check the current monitor status
  CURRENT_STATUS=$(xset q | grep "Monitor is" | awk '{print $3}')

  # Only turn the backlight on/off if the Monitor state has changed
  if [ "$CURRENT_STATUS" != "$LAST_STATUS" ]; then
    logger -p info -t "backlight_service" -s "Monitor is $CURRENT_STATUS"

    # Control backlight pin according to the monitor status
    if [ "$CURRENT_STATUS" = "On" ]; then
      logger -p info -t "backlight_service" -s "Turning Backlight On"
      raspi-gpio set $PIN dh
    else
      logger -p info -t "backlight_service" -s "Turning Backlight Off"
      raspi-gpio set $PIN dl
    fi
    LAST_STATUS=$CURRENT_STATUS
  fi

  # Sleep before checking again
  sleep 0.2s
done
</code>

==== Automatically Start the Service ====
Add the line ''@{/path/to/}backlight_service'' to the // /etc/xdg/lxsession/LXDE-pi/autostart // file or to the file // .config/lxsession/LXDE-pi/autostart // in the user's home directory to automatically start the //backlight_service// executable when the desktop starts.  See [[comfilepi:configure_a_program_to_auto-start:index#configure_an_x_program_to_auto-start_eg_mono|Configure an X Program to Auto-Start]] for more information.

To set the timeout to 60 seconds run ''xset dpms 0 0 60'' from a terminal.

Add the line ''@xset dpms 0 0 {timeout_in_seconds}'' to the //autostart// file to set the timeout each time the desktop loads.

Run ''journalctl -t backlight_service -r'' to view the log entries.