User Tools

Site Tools

한국어

cubase:index

CUBASE


CUBASE is series of base boards for the CUBLOC.

Warning



CUBASE-32M CUBASE-40M CUBASE-64M
CUBLOC Module CB280 CB400, CB405 CB290
Digital Inputs 16 Opto-Isolated 7.5 to 24V 24 Opto-Isolated 7.5 to 24V 32 Opto-Isolated 7.5 to 24V
Digital Outputs 12 Opto-Isolated 12 or 24V NPN TR 16 Opto-Isolated RELAY 32 Opto-Isolated 12 or 24V NPN TR
Analog Inputs 6 Channel 10-bit ADCs
Configurable Input Voltage: 0~5V or 0~10V
4 Channel 10-bit ADCs: 0~5V 8 Channel 10-bit ADCs
Configurable Input Voltage: 0~5V or 0~10V
Analog Outputs 6 Channel 16-bit PWMs
Configurable Modes: PWM or DAC(0 to 5V)
3 Channels 16-bit PWMs 6 Channel 16-bit PWMs
Configurable Modes: PWM or DAC(0 to 5V)
Counters 2 Channel 16-bit High Speed Counters for 7.5 to 24V DC Pulse Input (10kHz) 2 Channel 16-bit High Speed Counters for 5V Pulse Input (10khz) 2 Channel 16-bit High Speed Counters for 7.5 to 24V DC Pulse Input (10kHz)
Keypad Support Yes Yes Yes
CUNET, I2C Support Yes Yes Yes
LCD/7-Segment Support Yes Yes Yes
Power Required Power: DC 12 to 28V
Current Consumption w/ ports unloaded: @ 24VDC: 20mA
Isolated External 5 VDC Output: 5V/300mA
Required Power: DC 12 to 28V
Current Consumption w/ ports unloaded: @ 24VDC: 30mA
Isolated External 5 VDC Output: 5V/600mA
Required Power: DC 12 to 28V
Current Consumption w/ ports unloaded: @ 24VDC: 20mA
Isolated External 5 VDC Output: 5V/300mA
Insulation Resistance Input & Output & Input FG: DC500V, 100MΩ, Cut-off current: 10mA, 1Min Input & Output & Input FG: DC500V, 100MΩ, Cut-off current: 10mA, 1Min Input & Output & Input FG: DC500V, 100MΩ, Cut-off current: 10mA, 1Min
Vibration 10~50Hz at 2G for 3 minute period, 30 minutes along X,Y and Z axis 10~50Hz at 2G for 3 min. period, 30 min. along X,Y and Z axis 10~50Hz at 2G for 3 minute period, 30 minutes along X,Y and Z axis
Impact 10G for 20mS, Once on each X,Y and Z axis 10G for 20mS, Once on each X,Y and Z axis 10G for 20mS, Once on each X,Y and Z axis
Operating Temp. -10˚C to 50˚C (10% to 95% RH Non-Condensing) -10˚C to 50˚C (10% to 95% RH Non-Condensing) -10˚C to 50˚C (10% to 95% RH Non-Condensing)
Storage Temp. -10˚C to +70˚C (10% to 95% RH Non-Condensing) -10˚C to +70˚C (10% to 95% RH Non-Condensing) -10˚C to +70˚C (10% to 95% RH Non-Condensing)
Schematic Schematic Schematic
IO Map IO Map IO Map
Buy Buy Buy

Programming the CUBLOC Core Module

To program the CUBLOC core module, you will need to use CUBLOC Studio: Download for free. With CUBLOC Studio installed on your PC, you can then write programs using BASIC or Ladder Logic.

To download programs to the CUBLOC module, connect your PC to the CUBASE’s download port with an RS-232 cable. If your PC does not have an RS-232 port (COM port), you can use a USB to RS-232 converter. USB to RS-232 converters are available on our website.

For more detailed information about programming the CUBLOC, please refer to the CUBLOC User’s Manual.

Please refer to the schematic and IO map links above or the CUBASE’s PCB for CUBLOC port mappings.

Connecting Inputs and Outputs

The CUBASE 32M has 2, 8-pin, input port blocks for a total of 16 digital inputs. Each port block has its own common voltage reference pin labeled “COM1” through “COM4”. All input voltages are measured relative to its respective port block’s common voltage reference pin.

The CUBASE 64M has 1, 8-pin output port block and 1, 4-pin output port block for a total of 12 digital outputs. Each output port block has an output voltage pin labeled “+24V”. The output voltage pins are wired to the CUBASE’s supply voltage, so while this is typically +24V, it all depends on the voltage you supply the CUBASE.

The image above shows the CUBASE 32M connected to a Relay8 Board with an RCable. Using the RCable, the Relay8 board is powered by the CUBASE’s +24V supply voltage.

Display Devices

The CUBASE’s CSG and CUNET ports are I2C ports that can be used to interface to Comfile Technology’s various display devices.

The CSG port is for interfacing to Comfile Technology's 7-segment display devices (CSG-4M, CSG-4S). However, using the Set I2C command, CSG output can also be sent to the CUNET ports.

The CUNET port is for interfacing to Comfile Technology's character LCD (CLCD) devices (CLCD420-B, CLSD420-G, CLCD216-G) or any other CUNET/I2C device

CLCD and CSG devices interface cable can be up to 3 meters in length. A 1-meter cable is available on our website.

Keypad Devices

The keypad port can be used to interface to Comfile Technology’s keypad input devices.

COMFILE Technology's Keypads

COMFILE Technology's Keypad Controller

DIN Rail Mounting

The CUBASE can be mounted to a DIN Rail using Comfile Technology’s DIN Rail brackets. Simply attach the DIN Rail bracket to the back of the CUBASE and fasten with two screws.

COMFILE Technology's Documentation Library

cubase/index.txt · Last modified: 2023/09/25 09:31 by COMFILE Technology