modport:md-adin4:index
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
modport:md-adin4:index [2023/04/28 22:17] COMFILE Technology [Specification] |
modport:md-adin4:index [2023/05/31 04:34] (current) COMFILE Technology [4-Channel Analog to Digital Input Module: MD-ADIN4] |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ====== MD-ADIN4 ( AD Input Module ) ====== | + | ====== 4-Channel Analog to Digital Input Module: MD-ADIN4 ====== |
| - | ^Output Value ^Resolution ^Precision ^Conversion Speed^ | ||
| - | |0 ~ 10,000 |13.30bit| ±0.1% |30ms per channel| | ||
| The AD Input Modules can be wired to read voltage sources or current sources. | The AD Input Modules can be wired to read voltage sources or current sources. | ||
| - | {{ :modport:md-adin4:md-adin4.png?700 |}} | + | {{ :modport:md-adin4:md-adin4.png?600 |}} |
| When reading voltages sources, the modules can be configured for a 0 ~ 10V range or a 1 ~ 5V range using the dipswitch on the side of the module. | When reading voltages sources, the modules can be configured for a 0 ~ 10V range or a 1 ~ 5V range using the dipswitch on the side of the module. | ||
| Line 15: | Line 13: | ||
| {{ :modport:md-adin4:dipswitch.png?nolink |}} | {{ :modport:md-adin4:dipswitch.png?nolink |}} | ||
| - | |||
| - | |||
| ===== Specification ===== | ===== Specification ===== | ||
| - | ^Item ^Description^ | + | ^ Item ^ Description ^ |
| - | |Operating Temperature |-10 ~ 50 (no condensation)| | + | | Channels | 4 | |
| - | |Operating Humidity|35 ~ 85%RH| | + | | Operating Temperature | -10 ~ 50 (no condensation) | |
| - | |Input Resistance |20K ohms| | + | | Operating Humidity | 35 ~ 85%RH | |
| - | |Input Voltage Range |1~5V mode: 0.5 ~ 5.5V (Single-ended) \\ 0~10V mode: -0.5 ~ 10.5V (Single-ended)| | + | | Input Resistance | 20K ohms | |
| - | | Output Value | 0 ~ 100,000 | | + | | Input Voltage Range | 1~5V mode: 0.5 ~ 5.5V (Single-ended) \\ 0~10V mode: -0.5 ~ 10.5V (Single-ended) | |
| - | | Resolution | 16.6-bit | | + | | Output Value | 0 ~ 10,000 | |
| + | | Resolution | 13.3-bit | | ||
| | Precision | ±0.1% | | | Precision | ±0.1% | | ||
| - | | Conversion Speed | 240ms per channel | | + | | Conversion Speed | 30ms per channel | |
| | Communication Method | RS485 | | | Communication Method | RS485 | | ||
| | Packet Transmission | 3ms | | | Packet Transmission | 3ms | | ||
| | Isolation Method | No Isolation | | | Isolation Method | No Isolation | | ||
| + | |||
| + | |||
| + | |||
| **Important**: The AD Input Modules' inputs are not isolated, so please be sure to not provide voltage or current in excess of the specified ranges. Doing so could cause permanent damage. | **Important**: The AD Input Modules' inputs are not isolated, so please be sure to not provide voltage or current in excess of the specified ranges. Doing so could cause permanent damage. | ||
| Line 69: | Line 69: | ||
| ^Channel ^0 ^1 ^2 ^3 ^ | ^Channel ^0 ^1 ^2 ^3 ^ | ||
| |Starting Address(base 10) | 100 | 101 | 102 | 103 | | |Starting Address(base 10) | 100 | 101 | 102 | 103 | | ||
| - | |Starting Address(base 16) | 64 | 65 | 66 | 67 | | + | |Starting Address(base 16) | 64 | 65 | 66 | 67 | |
| - | |Address (base 10) used by HMI (SCADA) | 00101 | 00102 | 00103 | 00104 | | + | |Address (base 10) used by HMI (SCADA) | 40101 | 40102 | 40103 | 40104 | |
| ===== Module ID (Modbus Slave Address) Assignment ===== | ===== Module ID (Modbus Slave Address) Assignment ===== | ||
| Line 76: | Line 76: | ||
| Rotary switch position 0 corresponds to Modbus slave address 10. If the ID is changed after the module is powered on, it must be power cycled for the new ID to take effect. | Rotary switch position 0 corresponds to Modbus slave address 10. If the ID is changed after the module is powered on, it must be power cycled for the new ID to take effect. | ||
| + | |||
| + | [[modport:index|MODPORT]] | ||
modport/md-adin4/index.1682687842.txt.gz · Last modified: 2023/04/28 22:17 by COMFILE Technology