modport:md-daout2:index
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
modport:md-daout2:index [2023/04/29 12:44] COMFILE Technology |
modport:md-daout2:index [2023/05/31 04:35] (current) COMFILE Technology [2-Channel Digital to Analog Voltage Output Module: MD-DAOUT2] |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ====== MD-DAOUT2 - 2 Channel Digital to Analog Voltage Output Module ====== | + | ====== 2-Channel Digital to Analog Voltage Output Module: MD-DAOUT2 ====== |
| The MD-DAOUT2 is a 2-channel digital to analog voltage, 0~5V / 0~10V, output module. | The MD-DAOUT2 is a 2-channel digital to analog voltage, 0~5V / 0~10V, output module. | ||
| The voltage range is configured using the dipswitch on the side of the module. | The voltage range is configured using the dipswitch on the side of the module. | ||
| - | {{ :modport:md-daout2:md-daout2.png?700 }} | + | {{ :modport:md-daout2:md-daout2.png?550 }} |
| + | |||
| + | ===== Specification ===== | ||
| + | ^ Item ^ Description ^ | ||
| + | | Channels | 2 | | ||
| + | | Operating Temperature | -10 ~ 50℃ (no condensation) | | ||
| + | | Operating Humidity | 35 ~ 85%RH | | ||
| + | | Input Resistance | 20KΩ | | ||
| + | | Analog Output | DC 0~5V Or 0~10V (1KΩ or higher load) | | ||
| + | | Output Value | 0 ~ 60,000 | | ||
| + | | Conversion Speed | 30ms per channel | | ||
| + | | Communication Method | RS485 | | ||
| + | | Maximum Conversion Rate | 0 ~ 60,000, 600ms | | ||
| + | | Isolation Method | No Isolation | | ||
| + | |||
| + | ===== Output Voltage ===== | ||
| + | |||
| + | Values between 0 ~ 60,000 correspond linearly to the output voltage (0 ~ 10V, dipswitch OFF / 0 ~ 5V, | ||
| + | dipswitch ON). | ||
| + | |||
| + | {{ :modport:md-daout2:daout_chart.png }} | ||
| + | |||
| + | |||
| + | ===== Modbus Starting Address ===== | ||
| + | |||
| + | Each module has 2 channels, each with its own unique Modbus address. | ||
| + | |||
| + | ^Channel ^0 ^1 ^ | ||
| + | |Starting Address(base 10) | 3300 | 3301 | | ||
| + | |Starting Address(base 16) | CE4 | CE5 | | ||
| + | |Address (base 10) used by HMI (SCADA) | 43301 | 43302 | | ||
| ===== Module ID (Modbus Slave Address) Assignment ===== | ===== Module ID (Modbus Slave Address) Assignment ===== | ||
| Line 11: | Line 41: | ||
| Rotary switch position 0 corresponds to Modbus slave address 10. If the ID is changed after the module is powered on, it must be power cycled for the new ID to take effect. | Rotary switch position 0 corresponds to Modbus slave address 10. If the ID is changed after the module is powered on, it must be power cycled for the new ID to take effect. | ||
| + | |||
| + | [[modport:index|MODPORT]] | ||
modport/md-daout2/index.1682739854.txt.gz · Last modified: 2023/04/29 12:44 by COMFILE Technology